Vinyl

Buy a Used Turntable in 8 Checks: Speed, Bearings, Tonearm, Cartridge and Hum

What to test, what is cheap to fix and what should make you walk away

Black and white image of a vintage vinyl record player with a floral arrangement.

Illustration: a record, as a placeholder for the cover photo.

A 1970s deck with a sound bearing and a straight arm will outlast most new budget turntables. A deck with a worn bearing or a damaged arm is scrap at any price. Take a record you know well, a small torch and a phone with a speed app such as RPM Speed & Wow. Ask the seller to have it connected to an amplifier.

The 8 checks

  1. Measure speed at 33 and 45. Place the phone on the platter and run the app for 30 seconds at each speed. Aim for within 0.5% of nominal and wow-and-flutter under about 0.15%. Many Technics decks have strobe dots on the platter rim. Under the built-in neon lamp they should stand still with the pitch slider at zero. If the pitch control needs to sit near one end to reach correct speed, the speed circuit needs adjusting or repair.

  2. Watch the motor start. A healthy direct-drive deck like the Technics SL-1200 MK2 reaches speed in under a second. A belt-drive deck should settle within a few seconds without hunting up and down. On a belt-drive deck, lift the platter and look at the belt. A shiny, stretched or sticky belt costs £10–20 to replace, so treat it as a bargaining point rather than a fault.

  3. Spin the platter by hand with the motor off. It should coast smoothly and silently. Grinding, a rough spot or a short coast points to a dry or worn main bearing. Grip the platter edge and try to rock it sideways. Any clunk or play means the bearing is worn. On a Thorens TD-160 or Rega Planar 3 that is fixable. On many plastic-chassis decks it is not worth fixing.

  4. Test the tonearm bearings. Lift the arm off its rest. Hold it near the headshell and very gently try to wiggle it up and down and side to side. You should feel no play at all, only free, smooth movement. Rough or notchy bearings cause mistracking and distortion, and replacing them costs more than most budget decks are worth. Also sight along the arm tube to make sure it is straight.

  5. Use the cueing lift. Raise the arm with the lever, then lower it. It should drop slowly, taking two or three seconds. A sudden drop means the silicone damping fluid has dried out. The fix is cheap, but until it is done the lift will chip styli. Also check the arm stays put once it is lifted and does not drift across the record.

  6. Inspect the cartridge and stylus with the torch. Look for a bent cantilever or missing tip. Then assume the stylus needs replacing anyway, because you cannot know its hours. Find out whether a replacement is still made. Check whether the headshell is the standard SME-type bayonet fitting, which takes any cartridge. A proprietary fitting limits your options. Budget £50–120 for something like an Audio-Technica VM95E or Ortofon 2M Red.

  7. Play a record and listen for hum and crackle. Turn the volume up between tracks. A loud 50Hz hum usually means a missing or disconnected earth wire, which is easy to fix. Crackle when you touch the phono leads, or one channel cutting out, suggests frayed hardwired cables or failing tonearm wiring. Operate every switch and knob while the record plays. Scratchy controls need contact cleaner at minimum.

  8. Check the plinth, suspension and lid. Sprung-chassis decks like the Thorens TD-150 and TD-160 should sit level and bounce evenly when pressed. Lift the dust cover and let it rest open. Technics hinges in particular go brittle and won't hold. Replacements exist but add cost. Look under the deck for missing feet and signs of amateur repair: mismatched screws, glue or cut wires.

Common used decks and what to check first
Model Typical UK used price Known weak point
Technics SL-1200/1210 MK2 £400–650 Pitch slider dirt, hinge breakage, tonearm bearing wear on DJ-used units
Pioneer PL-12D £80–150 Stretched belt, dried cueing damper
Thorens TD-160 £200–400 Suspension springs out of level, tired belt
Rega Planar 2/3 (pre-2000) £180–350 Worn main bearing, cracked glass platter edges
Dual 1219/1229 £100–200 Gummed-up autochanger grease, sticking mechanism
Garrard 401 / Lenco L75 £250–700 Idler wheel hardening causing rumble and speed drift

Before you buy, check what you're connecting it to. Almost no vintage deck has a built-in phono preamp. If your amplifier lacks a phono input, add £40–100 for an external phono stage, and match it to the cartridge type: moving magnet (MM) for most budget cartridges, or moving coil (MC).

Where the money goes after purchase

A sound deck from a house clearance often needs a belt, a stylus and an hour with a cleaning brush and contact cleaner. That comes to around £70–150 all in. Repairs to bearings, motors or arm wiring are a different scale of cost. If check 3, 4 or 7 fails, the price should drop by more than the repair would cost, or you should leave it.

Arthur Pendelton

Lead Vintage Audio & Hi-Fi Reviewer

Arthur has spent over three decades hunting down rare original pressings and restoring classic turntable setups. A former sound engineer from London, he specializes in deep dives into jazz pressings, analog equipment maintenance, and the art of speaker placement. When he isn't writing, Arthur can usually be found at local record fairs digging through bargain bins.

Comments (0)

No comments yet. Be the first to share your experience.

Leave a comment

Comments are published after moderation.

The Weekly Groove

Get new records in your inbox

New guides, tips on finding vinyl, and one album breakdown every week. No spam.