Care

Clean Records in an Ultrasonic Tank in 7 Steps: Degassing, Surfactant, Spacing and Temperature

Distilled water, a few drops of surfactant, careful spacing and a thermometer get the grooves clean without risking the vinyl

A serene image of tranquil, crystal clear turquoise water surface with gentle ripples.

Illustration: a record, as a placeholder for the cover photo.

Ultrasonic cleaning reaches the bottom of the groove without anything touching the vinyl. A transducer vibrates the water at 40 kHz or higher, which forms millions of microscopic bubbles. When those bubbles collapse against the record surface, they lift out fine debris that brushes and vacuum machines push around. The process only works if the bath, chemistry and temperature are right.

The Process

  1. Choose your setup. Integrated units such as the Degritter, HumminGuru and Klaudio handle rotation, filtering and drying in one box. A DIY rig costs less. You need a 6–10 litre ultrasonic tank at 40 kHz, a motorised rotisserie such as the CleanerVinyl or Vinyl Stack, and a drying rack. Buy a tank with a heater you can switch off, or without a heater at all.

  2. Dry-clean first. Ultrasonic cavitation is good at fine particles and weak at greasy fingerprints and caked grime. Give every record a pass with a carbon fibre brush. Badly soiled charity-shop finds need a manual wet scrub before they go in the tank. Otherwise their dirt ends up in the bath and on the next record.

  3. Fill with distilled water and degas it. Use distilled or deionised water only, because tap water leaves mineral spots in the grooves. Fill to a level that covers the playing surface up to the lead-out groove but stays below the label. Then run the tank empty for 10 minutes. Fresh water is full of dissolved gas, which cushions the bubbles and weakens cleaning.

  4. Add a small amount of surfactant. A surfactant lowers surface tension so water can enter the groove. Tergitol 15-S-9 at around 0.01–0.02% is a common choice. That works out to roughly 1 ml in a 6-litre tank. Ilford Ilfotol works in similar tiny amounts. Avoid washing-up liquid, which foams and leaves residue. Do not put isopropyl alcohol in a tank that warms up, because the fumes are flammable and the alcohol can attack some label inks.

  5. Load with label protection and proper spacing. Clamp each record between screw-on label protectors or the rotisserie's caps so the label stays dry. Leave about 25–30 mm between records. If they sit too close, the cavitation weakens on the facing surfaces. Most 6-litre tanks take four to six LPs at once.

  6. Run the cycle and watch the temperature. Rotate at about 1 rpm for 5–10 minutes. Cavitation heats the water by itself, often 2–3°C per cycle, even with the heater off. Keep a probe thermometer in the bath and stop when it reaches 35°C. Above that, thin pressings start to risk warping. Let the bath cool, or add cold distilled water, before the next batch.

  7. Rinse, dry and resleeve. Dip each record in a second tank or bucket of plain distilled water, or mist it with a spray bottle. This removes surfactant left on the surface. Then do one of the following:

    • Stand the records in a drying rack with a small fan for 15–20 minutes.
    • Run them through a vacuum machine on a dry pass.

    When they are fully dry, put them in new anti-static inner sleeves such as Mobile Fidelity Original Master Sleeves. Change the bath after 25–30 records, or sooner if the water looks cloudy. A cartridge filter, such as a small pond or aquarium pump, extends the life of the water.

Test where your tank actually cleans with aluminium foil. Lower a strip of kitchen foil vertically into the running bath for 30–60 seconds. Areas pitted with tiny holes are where cavitation is strong. Smooth areas are dead spots. If the record's playing surface passes through a dead zone, change the water level or the rotisserie height until the foil shows even pitting across that band.

Chloe Sterling

Modern Collector & Vinyl Care Specialist

Chloe is a music archivist dedicated to helping new collectors protect and preserve their vinyl records. With a background in chemistry and library science, she writes accessible guides on record cleaning, storage solutions, and inner sleeve materials. Her goal is to ensure every collection survives for generations to come.

Comments (0)

No comments yet. Be the first to share your experience.

Leave a comment

Comments are published after moderation.

The Weekly Groove

Get new records in your inbox

New guides, tips on finding vinyl, and one album breakdown every week. No spam.