Vinyl

How to Read a Run-Out Groove in 6 Steps: Matrix Numbers, Stamper Codes and Cutter Signatures

What the scratches between the last track and the label tell you, and how to use them at the shop counter

Vintage vinyl record player with close-up of needle on black gramophone, creating a nostalgic music vibe.

Illustration: a record, as a placeholder for the cover photo.

The smooth band between the final groove and the label, the dead wax or run-out, is the only part of a record the sleeve and label can't lie about. Labels get reprinted and sleeves get swapped, but the etchings were cut into the lacquer or metalwork at the factory. Reading them takes a torch, a little patience and the six steps below.

What You Need

A small LED torch or your phone light, held at a low angle. Etchings are shallow and vanish under overhead light. A magnifier helps with hand-scratched marks. Tilt the record slowly until the characters catch the light.

The 6 Steps

  1. Find the matrix number. This is the core identifier, usually the longest string, often starting with the catalogue prefix. On UK Parlophone Beatles LPs it reads like YEX 749-2 (Abbey Road side one). XEX denotes a mono lacquer and YEX a stereo one at EMI. On US Columbia it might be XSM 47325. Check that it matches the side and the catalogue number on the label. A mismatch can mean a mispress, which is sometimes collectable and sometimes simply wrong.

  2. Read the suffix after the matrix. The number after the dash or space is the lacquer cut. -1 is the first lacquer accepted for that side. Columbia used letter-number pairs such as 1A, 1B and 2C. Low numbers usually mean early pressings, but not always: a later lacquer could go into service while earlier ones were still pressing. The famous case is the UK mono Revolver. Copies with side two matrix XEX 606-1 carry an alternate mix of "Tomorrow Never Knows" that was withdrawn within days, so -2 copies are common and -1 copies sell at a premium.

  3. Decode the stamper or mother code. Many UK pressings carry a separate number and letters, often at roughly 9 or 3 o'clock. EMI used the word GRAMOPHLES as a cipher: G=1, R=2, A=3, M=4, O=5, P=6, H=7, L=8, E=9, S=0. A mother number "1" with stamper "GO" means the first mother and the 15th stamper made from it. Decca used BUCKINGHAM the same way (B=1, U=2 and so on, through M=0). Low mother and stamper numbers mean the copy was pressed early in the run, when the metalwork was fresh.

  4. Look for the cutting engineer's mark. US collectors chase these especially. Some common ones:

Common cutting signatures in US and UK dead wax
Mark Engineer / Facility Where you'll see it
RL Robert Ludwig (Sterling, Masterdisk) Led Zeppelin II "RL" first cut, 1969
VAN GELDER / RVG Rudy Van Gelder Blue Note and Prestige, 1950s–60s
STERLING Sterling Sound, NYC Countless 1970s US rock LPs
MASTERDISK Masterdisk, NYC 1970s–80s US pressings
TML The Mastering Lab (Doug Sax), LA Steely Dan, Supertramp
Porky Prime Cut / Pecko George Peckham, London UK rock and punk, 1970s–80s
  1. Distinguish stamped from hand-etched. Machine-stamped characters are uniform and evenly spaced. Hand-scratched ones wobble. Some labels switched methods mid-run. On original Blue Note pressings, the stamped "VAN GELDER" (used from about 1957) sits alongside the hand-etched "RVG" and the "ear" (a hand-etched P, the Plastylite plant mark). These marks are the quickest way to separate a 1960s original from a 1970s Liberty reissue in a similar sleeve.

  2. Cross-check on Discogs before buying. Open the release page and scroll to "Barcode and Other Identifiers". Many pressings list the run-out text exactly. Find the entry that matches your copy character for character. Then check the marketplace history for that specific version, not the release overall. Two copies with identical labels can sell for £15 and £150 depending on one digit in the dead wax.

Watch Out For

  • Bootlegs and counterfeits often have a cleanly stamped matrix with no engineer mark, or a matrix etched in a single neat hand where the original used mixed methods.
  • Reissues using original metalwork. Some labels re-pressed from old stampers for years. Low matrix numbers alone don't prove an early pressing, so check the label design and sleeve details too.
  • Scratched-out numbers. A crossed-out matrix with a new one beside it usually means a lacquer was renumbered or reassigned. It's interesting, but rarely valuable on its own.

Photograph both sides of the dead wax before you leave a shop or meet a seller. Matching the run-out text on Discogs later is far easier than squinting at it under shop lighting, and it gives you a record if a "first pressing" claim turns out to be wrong.

Arthur Pendelton

Lead Vintage Audio & Hi-Fi Reviewer

Arthur has spent over three decades hunting down rare original pressings and restoring classic turntable setups. A former sound engineer from London, he specializes in deep dives into jazz pressings, analog equipment maintenance, and the art of speaker placement. When he isn't writing, Arthur can usually be found at local record fairs digging through bargain bins.

Comments (0)

No comments yet. Be the first to share your experience.

Leave a comment

Comments are published after moderation.

The Weekly Groove

Get new records in your inbox

New guides, tips on finding vinyl, and one album breakdown every week. No spam.