Set Up a Turntable Tonearm in 7 Steps: Levelling, Alignment, Tracking Force and Anti-Skate
The order to do it in, the numbers to aim for and the £15 tool worth buying

Illustration: a record, as a placeholder for the cover photo.
A cartridge that is badly set up costs you twice. It sounds worse, with smeared sibilants and a lopsided stereo image, and it wears grooves faster. Most decks under £500 can be dialled in properly with a protractor, a stylus gauge and about an hour. Work in this order, because each step depends on the one before it.
What you need
- A small bubble level. A spirit level app laid on the platter works at a pinch.
- A cartridge alignment protractor. Free printable Baerwald and Stevenson versions are available from Vinyl Engine. Print at 100% scale and check the test ruler with a real ruler.
- A digital stylus force gauge. Unbranded 0.01g models cost around £15 and are far more reliable than the counterweight markings.
- A small cross-head screwdriver and a hex key for the headshell bolts.
- A torch and a small mirror.
The 7 steps
-
Level the plinth. Put the level on the platter, not the plinth. The platter is what matters. Check it front to back and side to side. Adjust the deck's feet if they are adjustable, or shim under the furniture if they aren't. A tilted deck pulls the arm sideways and undoes your anti-skate setting later.
-
Mount and wire the cartridge. Connect the four tonearm leads by colour:
- White to left +
- Blue to left −
- Red to right +
- Green to right −
Push the clips on with tweezers, not fingers, because the pins bend easily. Fit the mounting bolts finger-tight so the cartridge can still slide in the headshell slots. Keep the stylus guard on.
-
Align overhang and offset. Place the protractor on the spindle and lower the stylus onto the inner null point. Slide and twist the cartridge until the front edge of the body, or the cantilever itself, sits parallel to the grid lines. Repeat at the outer null point. You will usually go back and forth three or four times. When both points line up, tighten the bolts evenly and recheck, because tightening often nudges the cartridge.
-
Zero-balance the arm. Set anti-skate to zero. Remove the stylus guard. Rotate the counterweight until the arm floats level, hovering just above the platter without rising or dropping. Then hold the counterweight still and turn only the numbered ring to 0.
-
Set tracking force. Rotate the whole counterweight towards the pivot to your cartridge's recommended figure. Two common examples:
- Audio-Technica VM95E: 2.0g, within a 1.8–2.2g range
- Ortofon 2M Red: 1.8g
Then confirm the reading on the digital gauge. Place the gauge so the stylus sits at roughly record-surface height. If the gauge disagrees with the dial, trust the gauge. Aim for the middle or upper half of the maker's range. Tracking slightly heavy is safer than too light, because a mistracking stylus chatters against the groove walls and does more damage.
-
Set anti-skate. As a starting point, match the anti-skate value to the tracking force. On Rega arms, which use a sprung slider, start one mark lower. Fine-tune by ear with a sibilant-heavy vocal near the end of a side, where distortion is worst. If "s" sounds splash more in one channel, adjust a notch at a time. A test record such as the Hi-Fi News Analogue Test LP makes this precise.
-
Check VTA and azimuth.
- VTA (vertical tracking angle): With the stylus lowered on a record, the arm should run parallel to the record surface when viewed from the side. If the pivot end sits high or low, adjust arm height if your deck allows it. Budget decks like the AT-LP120X do have this adjustment.
- Azimuth: Set a mirror on the platter, lower the stylus onto it, and look at the cartridge from the front. The cartridge and its reflection should form a straight vertical line. A visible lean usually means the headshell is twisted in its collar or the cartridge is seated unevenly.
After setup
Play a familiar record all the way through, paying attention to the last track of each side. Inner-groove distortion is the first thing a poor setup reveals.
Recheck tracking force after a week. Suspension in new cartridges settles during the first 20 or so hours of play.
Write down your final settings and stick the note under the platter mat: the tracking force, the anti-skate value and the arm height mark. When you change records cleaners, move house or knock the arm, you can restore everything in five minutes instead of starting over.






Comments (0)
No comments yet. Be the first to share your experience.